B.E. EIGHT SEMESTER SYLABUS ( Mechanical Engineering)

……………………………………………………………………………………….

BEME802P2: ELECTIVE – II : COMPUTER INTEGRATED

MANUFACTURING (Practical)

CREDITS: 01

Teaching Scheme Examination Scheme

Practical: 2 Hours/Week University Assessment: 25 Marks

College Assessment: 25 Marks

LIST OF PRACTICALS:

Minimum Eight out of the following shall be performed (out of which six must be experimental):

1. Introduction to CIM. (Product Development Cycle, CIM Wheel)

2. Introduction to NC. (Basic components, classification)

3. Manual Part Programming – Lathe.

4. Manual Part Programming – Milling.

5. Manual Part Programming by using Sub routine & Canned Cycles.

6. Part classification and Coding using G.T.

7. Study of F. M. S.

8. Study of CAPP Systems. (Retrieval & Generative)

9. Study of different quality measurement tools.

10. Assignment on implementation of CIM in Industry.

BEME802P5: ELECTIVE – II: REFRIGERATION AND

AIRCONDITIONING (Practical)

CREDITS: 01

Teaching Scheme Examination Scheme

Practical: 2 Hours/Week University Assessment: 25 Marks

College Assessment: 25 Marks

LIST OF PRACTICALS:

Minimum Eight out of the following shall be performed (out of which six must be experimental):

1. To perform experiments on vapour compression test rig to determine COP of the system.

2. Study of various types of compressor.

3. Study of various types of condenser, expansion devices and evaporators used in RAC.

4. Study of various types of air conditioning systems

5. To perform experiments on Air-conditioning test rig.

6. Study & performance of window air conditioner.

7. To perform experiments on desert cooler to evaluate its performance.

8. Demonstration of use of various tools and equipments used for installation, maintenance &

repair of refrigeration systems.

9. Testing and charging of vapour compression refrigeration system.

10. Report on visit to refrigeration plant/AC plant/cold storage plant.

BEME804P: AUTOMATION IN PRODUCTION (Practical)

CREDITS: 01

Teaching Scheme Examination Scheme

Practical: 2 Hours/Week University Assessment: 25 Marks

College Assessment: 25 Marks

LIST OF PRACTICALS:

Minimum Eight out of the following shall be performed:

1. Performance, Simulation on CNC lathe (at least two complex geometries).

2. Performance, Simulation on CNC milling (at least two complex geometries).

3. Practice Programming on Manual Part Program.

4. Practice Programming on APT.

5. Case Study on Automated System of any Industry.

6. Study/Performance on Robot.

7. Part Coding and Group Technology.

8. Study of Automation & Case Study of Automated System of any Industry.

9. Study of NC System.

LIST OF PRACTICALS:

At least eight Practicals in applications like Material Management, Inventory Management, Office automation etc. based on above syllabus shall be conducted using suitable DBMS packages like ORACLE, MS ACCESS etc. or relevant freeware/s.

Note:

During University practical examination of 50 marks, students are expected to workout

problem/s of total 30 marks using DBMS software in two hours duration. Viva-voce of 20

marks shall be conducted during University practical examination.

BEME805P: ENERGY CONVERSION - III (Practical)

CREDITS: 01

Teaching Scheme Examination Scheme

Practical: 2 Hours/Week University Assessment: 25 Marks

College Assessment: 25 Marks

LIST OF PRACTICALS:

Minimum Eight out of the following shall be performed:

1. Study of gas turbine and jet propulsion system.

2. Study of current energy scenario and various techniques of saving energy.

3. Study & demonstration of solar lightning system.

4. Case study on energy conservation opportunities in industry.

5. Study of various hydraulic pumps.

6. Study of various valves, actuators used in hydraulic system.

7. Study of various industrial hydraulic circuits.

8. Study of various compressors used in pneumatic system.

9. Study of air preparatory unit.

10. Study of various industrial pneumatic circuits.

B.E. SIXTH SEMESTER SYLABUS ( Mechanical Engineering)

……………………………………………………………………………

BEME604P: MECHATRONICS (Practical) CREDITS: 01

Teaching Scheme

Examination Scheme

Practical: 2 Hours/Week

University Assessment: 25

Marks

College Assessment:25

Marks

LIST OF PRACTICALS:

Minimum Eight practicals out of the following areas shall be performed:

1. Identification & study of solid state electronic devices.

2. Identification, study & demonstration of different sensors.

3. Identification, study & demonstration of different actuators.

4. Demonstration of working of various digital to analog and analog to digital Converters.

5. Development of ladder diagram, programming using PLC for any of the following.

a) Motor start and stop by using two different sensors.

b) Simulation of a pedestrian traffic controller.

c) Simulation of four road junction traffic controller.

d) Lift / elevator control.

e) Washing machine control.

f) Tank level control.

g) Soft drink vending machine control

h) Any other suitable application.

5. Trace, interpret and demonstrate working of electro pneumatic systems.

6. Trace, interpret and demonstrate working of electro hydraulic systems.

BEME605P: DYNAMICS OF MACHINES (Practical) CREDITS: 01

Teaching Scheme

Examination Scheme

Practical: 2 Hours/Week

University Assessment: 25

Marks

College Assessment:25

Marks

LIST OF PRACTICALS:

Minimum eight out of the following shall be performed:

1. Determination of jump-of speed of a typical cam- follower system.

2. Dynamic balancing of rotating masses(study of wheel balancing machine along with performance by visiting any automobile workshop).

3. Balancing of reciprocating mechanism.

4. Critical speed of shafts.

5. Performance characteristics of Gyroscope.

6. Free vibration of single DOF and two DOF spring mass system.

7. Natural frequency determination of cantilever beam.

8. Damping determination through free vibration logarithmic decay of a simple damped system.

9. Natural frequency determination of two and three rotor system.

10. Torsional vibration of bifilar or trifilar pendulum.

11. Transmissibility of single degree of freedom system

12. Dynamic vibration absorber.

13. Dynamic force analysis of four bar mechanisms.

14. Dynamic force analysis of slider crank mechanism.

15. Flywheel selection and parameter design for a typical multi-cylinder engines.

16. Performance characteristics of governors.

17. Study of any mechanism in workshop/industry..

18. Use of FFT analyzer for determination of natural frequencies of machine components.

BEME607P: COMPUTER APPLICATIONS – II (Practical) CREDITS: 04

Teaching Scheme

Examination Scheme

Practical: 2 Hours/Week

University Assessment: 50

Marks

Tutorial: 2 Hour/Week

College Assessment:50

Marks

LIST OF PRACTICALS:

At least eight Practicals in applications like Material Management, Inventory Management, Office automation etc. based on above syllabus shall be conducted using suitable DBMS packages like ORACLE, MS ACCESS etc. or relevant freeware/s.

BEME403P: HYDRAULIC MACHINES (Practical)

CREDITS: 01

Teaching Scheme Examination Scheme

Practical: 2 Hours/Week University Assessment: 25 Marks

College Assessment: 25 Marks

LIST OF PRACTICALS:

Minimum Eight out of following shall be performed:

1. To determine the metacentric height of given floating vessel.

2. To verify Bernoulli’s theorem.

3. To find the value of co-efficient of given venture meter fitted in a pipe.

4. To find the value of co-efficient of Discharge for a given orifice meter.

5. Performance characteristics of Pelton wheel.

6. Performance characteristic of Francis Turbine.

7. Performance characteristic of Kaplan Turbine.

8. Performance characteristic of Reciprocating pump.

9. Performance characteristic of Variable speed pump.

10. Performance characteristic of Axial Flow Pump.

11. To find friction losses in pipe.

12. To determine co-efficient of discharge in pipes.

BEME404P: MACHINING PROCESSES (Practical)

CREDITS: 01

Teaching Scheme Examination Scheme

Practical: 2 Hours/Week University Assessment: 25 Marks

College Assessment: 25 Marks

LIST OF PRACTICALS:

Minimum Eight out of following shall be performed:

1. Study of Single Point Cutting Tool.

2. Study of Various forces on single point cutting tools.

3. Study of multiple point cutting tools (milling, drilling)

4. Study of Lathe Machine.

5. Study of Shaper mechanisms.

6. Study of Broaching machines.

7. One Job on Milling.

8. One Job on Drilling, Boring

9. One Job on Thread Cutting, Taper Turning.

10. One Job on Surface Grinding.

11. One Job on Shaper.

BEME405P: MECHANICS OF MATERIAL (Practical)

CREDITS: 01

Teaching Scheme Examination Scheme

Practical: 2 Hours/Week University Assessment: 25 Marks

College Assessment: 25 Marks

LIST OF PRACTICALS:

Minimum Eight Practicals out of following areas shall be performed:

1. Study of Universal Testing Machine

1. Tension test on metals.

2. Compression test on materials.

3. Shear test on metals.

4. Impact test on metals.

5. Hardness test on metals.

6. Torsion test on metals.

7. Deflection of beams.

8. Modulus of rupture test.

9. Buckling of columns.

10. Deflection of springs.

………………………………………………………………………………………………………….